Garage glossary
Plain definitions of the terms used across our guides, each taken from the guide that explains it in full.
- Battery maintainer
A charger used for maintenance charging while a car is stored. It must suit the battery chemistry and the vehicle; the exact charger manual and vehicle handbook govern the setup.
Read: Battery maintainers for stored cars- Cavity wax
A treatment category for enclosed vehicle sections such as doors, sills and chassis members. A maker’s description of where a product can be used does not establish suitability for every vehicle, and a lance reaching a cavity does not prove complete coverage.
Read: Cavity wax explained- Change comparison
A comparison between observations made at different times. Keep a starting condition record so later comparison uses the same views; images cannot establish the condition of hidden or structural areas.
Read: Car rust inspection checklist: record before treating- Coating system
The compatible sequence of preparation products and coatings specified for an application. Compare it in the manufacturer’s documentation, and record what is included and what must be bought separately.
Read: Cavity wax vs underbody coating- Compressor dehumidifier
A dehumidifier type that may be a sensible option if the garage stays within that model’s useful temperature range. Compare the exact model’s manual and performance table.
Read: Choosing a dehumidifier for a cold garage- Condensation (inside a stored car)
Water on the inside of glass is a symptom, not a diagnosis. It can come from wet carpets, a leak, washing, or cabin air meeting cold glazing.
Read: Condensation inside a stored car: find the moisture source- Corrosion
Deterioration of a material through interaction with its environment. Corrosion on a structural or safety-critical component needs competent assessment; photographs and a checklist cannot establish remaining strength.
Read: Car rust inspection checklist: record before treating- Desiccant dehumidifier
A dehumidifier type that may suit a colder space, but it can draw more electricity at some settings. These are broad differences between technologies, not a substitute for the exact model’s figures.
Read: Choosing a dehumidifier for a cold garage- Drain holes
Model-specific openings that let water leave doors, sills and other sections. Identify them using vehicle-specific information rather than pushing tools into unknown holes.
Read: Car drain holes and water ingress: trace before clearing- E10 and E5 petrol
GOV.UK says most petrol vehicles can use E10 but identifies classic, cherished and older vehicles among those that may not be compatible. If a vehicle is not listed in its checker, GOV.UK says to continue with E5 when in doubt.
Read: E10, E5 and fuel in a stored classic car- Environmental note
A record of relevant surrounding conditions, such as water entry or condensation. Note it separately from what you can see of the affected area.
Read: Car rust inspection checklist: record before treating- Flat spots
Temporary or lasting tyre deformation that can develop while a car stands. The right storage action depends on the exact tyre, vehicle, duration and manufacturer guidance.
Read: Tyres and flat spots during car storageA state not established by the available visual observations. Write the inspection limits down rather than guessing.
Read: Car rust inspection checklist: record before treating- Hygrometer
An instrument that records relative humidity. It is most useful as a trend recorder; a reading describes the air at that moment and does not diagnose a damp wall or floor.
Read: Where to put a hygrometer in a garage- Lay-up
Taking a car out of use for a storage period, with a plan built around the car as it is now and a record left for the next start-up.
Read: Laying up a classic car: build a plan for your car- Lay-up period
A defined interval during which a vehicle is kept out of normal use. Record it with the vehicle identity and the photographs taken before storage.
Read: Washing and drying before storage- Prescribed area (MOT)
In the DVSA MOT inspection manual, the safety-critical parts of the structure that get particular attention: load-bearing parts carrying testable equipment, and supporting structure within 30cm of the mounting location.
Read: MOT corrosion failures: what testers check in prescribed areas- Recommissioning
Returning a stored car to use: read the storage record, inspect before moving and restore systems in a controlled order using the handbook.
Read: Recommissioning a car after storage- Return-to-use review
A review of the checks needed before normal use resumes. It is not a roadworthiness certificate, and starting successfully does not prove that all safety-related systems are ready for use.
Read: Recommissioning a car after storage- Rust converter
A product its maker describes as a converter for rusted steel and a base for further coatings. A converter and a protective wax have different intended jobs, and chemical treatment does not replace a repair decision.
Read: Rust converters and treatments: what to check- SORN
The DVLA notification for keeping an untaxed vehicle off the public road. Storage and notifying DVLA are separate tasks; read the current GOV.UK service for your circumstances.
Read: SORN and storing a car off the road- Starting condition
The recorded state before a storage or treatment period. Keep a starting condition record before treatment or storage so later change comparison uses the same views.
Read: Car rust inspection checklist: record before treating- Storage bubble
A powered enclosure for a stored car. It needs space, power and a maintenance routine; compare those requirements with your garage before considering protection claims.
Read: Car storage bubbles and airflow covers- Storage observation
A dated note made while an item is stored. Keep photographs alongside written storage observation notes.
Read: Washing and drying before storage- Substrate
The underlying surface to which a treatment or coating is applied. Do not assume that a product suitable for one surface or assembly is appropriate for another.
Read: Cavity wax vs underbody coating- Surface preparation
The work specified before applying a treatment or coating. Compare it in the manufacturer’s documentation alongside the intended substrate and application conditions.
Read: Cavity wax vs underbody coating- Treatment record
Notes identifying a product, preparation and application history. Keep it with the inspection photographs.
Read: Cavity wax vs underbody coating- Underbody coating
A treatment for the exposed underside with its own preparation, primer and maintenance requirements. A thick or dark finish does not establish how sound the metal is.
Read: Underbody rust protection: compare the job first- Underseal (old)
An existing underbody coating that may be intact, damaged, brittle, contaminated or covering previous repairs. Its appearance alone cannot establish the condition of the metal beneath it.
Read: Old underseal: inspect before repairing or recoating
Looking for an answer rather than a term? Try the knowledge base.