An MOT tester does not judge corrosion by its size or appearance alone. Location, the job done by the affected metal and the loss of strength all matter. A small corroded area can be serious when it weakens a safety-critical mounting; more extensive corrosion on a non-structural panel may be assessed under different criteria.
The rules below summarise the current DVSA MOT inspection manual for cars and passenger vehicles. They are not a remote assessment of any particular car, and no checklist can guarantee an MOT result.
What is a prescribed area?
In the manual, prescribed areas are the safety-critical parts of the vehicle structure that receive particular attention during an MOT. They include:
- load-bearing parts to which testable brake, steering, axle, wheel, tyre, suspension or Section 7 equipment is mounted
- load-bearing or supporting structure and supporting panelling within 30cm of the mounting location
Section 7 includes items such as seat belts, so corrosion around a seat-belt anchorage and the structure supporting it can be relevant. Other examples can include structure around suspension, steering and braking component mountings. The exact load path depends on the vehicle's construction: a sill may be structural on one design and play a different role on another.
The 30cm rule is not a general circle around every rusty patch. It starts from the mounting location of a testable item and applies to load-bearing or supporting structure within that distance. Nor does a sound-looking mounting end the assessment: the tester considers nearby panels and reinforcements that support it. The manual gives a seat-belt mounting on an inner sill as an example where the outer sill, reinforcement, door pillar, floor or other structural part within 30cm may matter.
How a tester assesses corrosion
The tester first identifies the important load-bearing members and prescribed areas. Assessment then progresses from a visual inspection to finger-and-thumb pressure. If needed, the tester may carefully scrape or lightly tap the area with the approved corrosion assessment tool.
That tool is used only to establish whether the failure criteria are met. The manual does not permit heavy scraping or aggressive probing. Areas hidden by items such as body trim do not have to be inspected, although visible supporting structure and other testable areas remain within the normal inspection.
Within a prescribed area, the manual says corrosion is rejected when it has made a hole, the metal is no longer firm under finger-and-thumb pressure, or pressure or the assessment tool creates a hole. A fracture or inadequate repair in a prescribed area is also a reason for rejection. A modification or severe distortion is rejected there when it significantly reduces the strength of a component mounting, load-bearing member or supporting structure or panel.
This is why surface colour is not the deciding factor. The relevant question is whether corrosion has crossed the manual's strength and condition thresholds in a structurally important location.
What testers look at beyond prescribed areas
Corrosion outside a prescribed area is not automatically irrelevant. Section 6.1.1 covers the vehicle's general structure away from prescribed areas. It lists a major defect where corrosion significantly reduces the rigidity of the assembly, and a dangerous defect where the condition is likely to affect steering or braking adversely.
Body condition has separate criteria. Under Section 6.2.1, a damaged or corroded body panel or component can be a major defect if it is insecure or likely to cause injury on contact; a part likely to detach is dangerous. Separate-body vehicles, body or cab mountings, towbars and engine mountings also have their own instructions in Section 6.
So "more than 30cm from a mounting" does not mean "cannot fail". It means the prescribed-area test may not be the applicable route; the general structure, body condition or another component-specific rule may still apply.
Repairs are assessed too
Structural repairs must be properly executed, use suitable materials and appear as strong as the original structure. Plating or welding must extend to sound metal on a load-bearing member. The manual generally requires patch repairs to be continuously seam welded, except for specified alternatives such as appropriate replacement of an originally spot-welded panel. It also recognises manufacturer-recommended methods including some combinations of MIG brazing, adhesive bonding and riveting.
Filler, fibre reinforcement, soldering, gas brazing and adhesive bonding on their own are not accepted as repairs to load-bearing members. Non-metallic load-bearing structures have separate rules, including that repairs in prescribed areas are not acceptable.
Repair design and execution are specialist work. Ask a competent repairer to identify the affected structure, the intended repair method and any vehicle-maker procedure before work starts. A cosmetic covering is not evidence that the underlying metal or repair meets the MOT criteria.
A sensible pre-MOT corrosion check
You can make a useful record without trying to reproduce an MOT inspection:
- Note visible corrosion, paint blistering, loose scale, holes and previous repairs without scraping or probing the metal.
- Record whether each area is fully visible, partly obscured or inaccessible.
- Photograph the wider location as well as the detail, including which side and which nearby mounting or structural feature is involved.
- Arrange safe workshop access for the underside and any area whose strength is uncertain.
- Ask the repairer to distinguish structural repair from later protective treatment.
Do not work beneath a vehicle supported only by a jack, and do not remove trim or underseal merely to investigate without an appropriate access and repair plan. If corrosion may affect safe use, obtain competent advice before driving rather than waiting for the MOT.
Our rust inspection checklist provides a repeatable way to record locations, access limits and workshop questions. If sound enclosed sections are being considered for protection after inspection or repair, cavity wax explained covers access, drains and treatment records. A protective coating is not a structural repair and should not be used to hide a condition that still needs assessment.
Sources
- DVSA MOT inspection manual, Appendix A: Structural integrity and corrosion - checked 9 November 2026; prescribed areas, assessment, failure criteria and repair methods.
- DVSA MOT inspection manual, Section 6: Body, structure and attachments - checked 9 November 2026; general structure, body condition and component-specific defects.
Sources & checks
Checked 2026-11-09. Read the original instructions before acting.